Search results

  1. RubberCtyRauder

    Fuel Cap Scratches

    First thing I did was cut that tether off. I don't need it dangling there. If you can't remember to put your gas cap back on.
  2. RubberCtyRauder

    How do you get c clip out of axle

    https://youtu.be/upUBWGsNTKc
  3. RubberCtyRauder

    Powerplant Transplant

    And oil pick up tube
  4. RubberCtyRauder

    Long Distance Marauder Ressurrection

    Smoky start up is common. Valve seals get old. Marauders and Cobras..also video shows as private, no viewing
  5. RubberCtyRauder

    Loud intake noise suddenly

    Any codes,CEL ? Whistling could be vac leak, air intake leak. Whistling can also be a pulley,idler. Kinda sounds like a centri unit. Does sound pitch change with throttle?
  6. RubberCtyRauder

    Tire size advice

    Must maintain 3-6% diameter difference front to rear with traction control.
  7. RubberCtyRauder

    Air compressor/spring question

    Could be..my original compressor lasted 15 ish years. Make sure the ride height sensor didn't move. Load the trunk with some weight and turn key on, and open and close door. My system holds air great. Hardly ever turns on, Original bags too
  8. RubberCtyRauder

    Would like some feedback...

    Some black rtv on the lower rear window seal and push it back on. Don't need alot of it. Door windows prolly need new weatherstrip. Once they are hard, nothing softens them.
  9. RubberCtyRauder

    Long time gearhead with new (to me) Marauder

    Call Mo's Speed Shop, Dallas,GA. They are a SW dealer, they know Marauders very well. You don't have to be or go to GA to benefit.
  10. RubberCtyRauder

    Rotor run out

    Put it in neutral on jack stands, keep one side tire on and have some one turn it. Switch and do other side
  11. RubberCtyRauder

    For Sale Marauder Emblems

    There could be someone here, but alot have gone to Facebook Marauder groups.
  12. RubberCtyRauder

    Replacing window control panel

    Try tascaparts.com or ebay, switch housing, cover It's just a plate that slides in ,if you lift it straight up the tabs break. All the wiring stays on the switch module,no unwiring required
  13. RubberCtyRauder

    Dragcity Marauder - Build it plan

    Many run 60lb, so I doubt it. Prolly best to talk with your tuner..Marty/Mo's I assume?
  14. RubberCtyRauder

    Dragcity Marauder - Build it plan

    I run 2.8 upper, 4lb lower. My compression is higher than yours. I don't know what as it was built before I got it. I run lfp intercooler and a killer chiller
  15. RubberCtyRauder

    Dragcity Marauder - Build it plan

    TR6 plugs..I have 495 rwhp with my trilogy and still on 39lb injectors. Depends on their duty cycle.
  16. RubberCtyRauder

    Addco front stabilizer bar rubbing/knocking/catching on inside brake/hub... HELP!

    Didn't Addco have a solid bar and a larger diameter hollow bar?
  17. RubberCtyRauder

    What Gear Ratio Should I Look For

    You can do a higher stall, 2800ish but not necessary as mentioned, the tune corrects shift points, speedo, keeps car in powerband and better than stock tune. Car will feel 800 lbs lighter.
  18. RubberCtyRauder

    Dragcity Marauder - Build it plan

    Marty can remote tune, you will need to be able to data log
  19. RubberCtyRauder

    Gas Mileage

    91 minimum. I don't check my mileage, not a daily driver, I would say more like 15 city pending your right foot.
  20. RubberCtyRauder

    Wanted To Buy Cold Air Intake support / shield needed

    I actually have a good used part "U" from the K&N diagram above. It has edge trim on it but it is not like the foam style in your pic
Back
Top